We're Listening...
This is the place for general feedback
Subforums
-
Contact Us
Use the options below to receive support for your specific problem.
Technical Support
- Post your problem in the forum! Our forum is moderated both by expert community gurus and the Unitronics' Support team--very often this is the fastest way to get help.
-
Submit a support request via our Support Portal, https://support.unitronics.com/index.php , or email us directly at support.unitronics.com.
Note that the Portal also includes a Knowledge-base: https://support.unitronics.com/index.php?/selfhelp/categories
Forum Issue
Are you having issues with the forum--difficulties logging in, resetting your password? Have you found a forum bug? Please write to us at Forum.Admin@unitronics.com
Do not write to individual Support Team Members and Forum Admins, please.
If the person you write to is off hiking the Himalayas, rafting the Amazon, walking the Appalachian Trail, on maternity/ paternity leave, you will not receive a timely answer.
May all your applications be bugless--from the Forum Admins (otherwise known as the Creators
)
- No posts here yet
)351 topics in this forum
-
- 18 replies
- 4.1k views
-
- 5 replies
- 3.4k views
-
- 5 replies
- 437 views
-
- 3 replies
- 1.1k views
-
- 6 replies
- 3k views
-
- 2 replies
- 4k views
-
- 14 replies
- 2.8k views
-
- 2 replies
- 464 views
-
- 11 replies
- 1.7k views
-
- 9 replies
- 6.9k views
-
- 0 replies
- 451 views
-
- 6 replies
- 1.7k views
-
- 1 reply
- 380 views
-
- 7 replies
- 4.8k views
-
- 9 replies
- 1.3k views
-
- 1 reply
- 591 views
-
- 2 replies
- 742 views
-
- 0 replies
- 458 views
-
- 2 replies
- 660 views
-
- 14 replies
- 4.6k views
-
- 4 replies
- 977 views
-
- 0 replies
- 464 views
-
- 2 replies
- 1.4k views
-
- 0 replies
- 592 views
-
- 2 replies
- 674 views
-
Member Statistics
8,493
Total Members1,206
Most Online
-
Topics
-
-
Who's Online (See full list)
-
Posts
-
By JRiddington · Posted
Hi guys, I have now tried starting a new project. Absolutely no ladder at all. I have still got the analog outputs directly wired to the analog inputs. Output 0 to input 0, and output 1 to input 1. I have scaled both inputs and outputs in the I/O settings to have a range from 0 to 10000, they are also both set to 0-10v. I created a watch table for all 4 (analog input 0 and 1, and analog output 0 and 1). If i understand correctly, if i send analog output 0 to a value of 1000 i should get 1000 back on the input? This is not the case i appear to get a value of 340 on the input. How can this be possible? The scaling is the same and one is directly connected to the other. I have checked the voltage and that appears to be correct just not the value of the input. -
Why aren't you using Layers? You can hide an entire layer while editing the HMI, so you won't have to send to back or bring to front. -
I followed the instructions to make a factory reset SD card but the tool's standard software still launches. It does read that there is an SD card inserted with the software though. Not sure if there is a jumper or some other reset function I'm supposed to engage first. -
By Joe Tauser · Posted
Yep. Subroutines are the way to go. You're on the right track. Joe T. -
As Gabriel said - how is your input scaled? Try linearizing the input over the voltage range you want. This will linearize a 14bit analog input over the 0-1000 mV range you need - setting input voltage equal to bar essentially. 2v = 2bar, 10v =10 bar
-
-
Blog Entries
-
