jblkiller

I would like to know if you can show me you HMI display with Vision that you created. I need some idea to create new project with the V700. I upload somes displays that I created first time with the V350 for somes projects. Thanks

I have 5 preset for this cable winder. 1) Slow down before stop 2) Stop the line at XX feet 3) Send a output pulse to the printer at 1/4 of length for cable identification 4) Send a output pulse to the printer at 1/2 of length for cable identification 5) Send a output pulse to the printer at 3/4 of length for cable identification Can I use the compare box (greater equal) to compare the length with a preset and output on when he reach the preset? The operator run the line at 400 to 1000ft/min. The plc will be fast enough to send a output at the good preset of length? My program has 25 rungs and when I test and go online with my laptop I see on SI0: 2.

How configure the HMI to see the speed in Feet/min.? In the hardware configuration I setup I1 to Frequency measurement 1000mSec in ML 1. (I0 is configurated Shaft encoder X4). How convert frequency to feet/min.? When the encoder turn one time is 1 feet. Encoder is a 100ppr, Thanks

Thanks

I have a Durant counter that I want replace by a V350-35-T38 because I need 4 preset. In the setup of Durant counter we have to enter count scale. I don't see how put this number in visilogic software. My encoder is a quadrature 100 ppi.

I have a M91-2-R1. How can we measure the speed of my conveyor with proximity switch. The conveyor go to approx 8 feet/min. and the sensor detect at all 1 feet.

DC drive with dc motor

I have a M91-2-R1 to make some test. I want replace Fusion counter by the plc for a winder. The counter have a encoder 100PPR. When the count reach Preset 1 the motor jog at X speed and when he reach the preset 2 he stop the motor for cutting the material. In the U90 software the are samples of HSC. But I don't see where can I put the number of PPR of the encoder?

Can we have a ziplink like : http://www.automationdirect.com/adc/Shopping/Catalog/Programmable_Controllers/CLICK_Series_PLCs_(Stackable_Micro_Brick)/ZipLink_Wiring_Solutions/ZL-RTB20 for cable a control box with many push button for the plc input?

Works perfectly!

Do I need two differents local port number?

I have a V350 with ethernet card. I setup a counter for the maintenance. I send a e-mail when the plc reach the counter. Work great. Also I would like control the plc with Remote Access? I try but don't work. For e-mail I setup the block ''TCP/IP - Socket init'' Master. But I can't connect to plc whith Remote acces when I configure with e-mail. Thanks. Can I send e-mail and use Remote Access?

Thanks you for the explanation!

I have a M91 into a box. I would like to have a acces to the RS232 port for troubleshooting whithout open the box. I connect the cable to a coupler like that: (http://www.digikey.ca/product-search/en?x=0&y=0〈=en&site=ca&KeyWords=a34359-nd) but the plc don't want communicate. I check the continuity for both cables and is ok. I there a maximum length for rs232? When I plug the plc direct to the pc with one cable is ok. When I connect two cable with the coupler don't work. Thanks

Thank you!

Should I use flyback diode on output with my M91-2-T1? I will drive Solenoïde valve with on-off at 2 secondes of interval. Thanks!

Which safe distance should place the master disconnect switch( 20A) above my V350 PLC? I don't want problem. Thanks

I add a serial to Ethernet converter to one of my M91 and works great! For only 130$ Brainboxes ES-246

If you were to put the encoder on the output shaft of the gearbox your maximum frequency will be 614 Hz, which will work fine. Can you do this? Yes I will slow motor down. I will make a test with a m91 spare before!

The PPR is 2048 because I need a precision stop load about 1/4 inch. The rotation of the encoder will be 1500 to 1800 rpm. The encoder will be mounting on the motor. The motor is a 1800 rpm and the ratio gearbox is 100:1. The gearbox is a allow shaft. I will try with a M91 spare unit for the moment! It will be the same program setup on Vision plc? Thanks

I have a new project that want to use Vision plc. I don't know if I can plug a incremental encoder HS35R with Z (homing). I have a motor with drive and gearbox who connected on the load. The load rotate clock wise but need to stop at 4 positions that the operator enter in the hmi. I would like to know if the vision plc can control a drive with HS35R encoder with Z (homing) for position? Thanks

I have a M91-2-R1 to control 2 heatgun and 2 exair cooling vortex tube. I use 120Vac scr to start the heatgun and 120Vac solénoïde valve for the cooling. Do I need a RC supressor or other protection for the contact of the plc? The cycle is 1. turn ON heater 7 sec. turn OFF heater and start cooling 7 sec. turn OFF cooling 2. turn ON heater 7 sec. turn OFF heater and start cooling 7 sec. turn OFF cooling 3. turn ON heater 30 sec. turn OFF heater We make this cycle 7 hours per day. Now I have a one bad contact relay. The M91-2-R1 is the best to control scr and solenoide valve? I chose this plc because I have a department that use 52 of this plc. Thanks!

I bought a new plc M91-2-R1. I put the new plc ON after 1.5 years after purchase. The plc go ON and dead and smell burning. I get out this one and put another and work great. I open the dead plc and you can see on pictures the state of the boards. http://img.photobuck...lc/DSC09425.jpg http://img.photobuck...lc/DSC09427.jpg http://img.photobuck...lc/DSC09430.jpg http://img.photobuck...lc/DSC09422.jpg What do you think? Can I return the product? Thanks

When implementing a timer throught the HMI and assign a timer operand to the variable . Can I block the maximum seconde for the operator can't go over?

I would like to know with the M91 if can I use a potentiometer plug into the analogue input (0-10V) to setup the time of a timer? Thanks