balazs.tarro-HUN

Hi everyone! I have an urgent issue to solve 🫤 In one of my working project a new issue has appeared with the following error message: I/O bus error [Code 0] After a reboot the PLC working fine for about 10-15 minutes and the error appears again. Let me show the PLC I/O configuration : I have just replaced the UAG-XKP300 (beetween the PLC and first row IOs) with a brand new one. Started the machine and it works fine...for about 15-20 minutes. The same error appears! I've checked the IOs and all of it blinks red slowly, except one of its! UID-0808THS (number #18 IO modul, after the second UAG-XKP300) blinks red rapidly. Now I try to change the second UAG with a new one. But before error appears again, does anybody have any idea what to do? Try to change CPU ? What does error 0 mean? Thank you! Unfortunately it is really important and should solve quickly 🤞 Best regard, Balazs

Hi, I have an issue when I try to download to PLC - only if I try it remotely!? I mean, if I connect my laptop directly to the PLC and I try to download via its own IP address everything goes well! If I try to download from another network, i.e: 4G network or from my home it causes issues the following warning: (01.jpg). As you can see at the 02.jpg picture the connection is fine (port forwards are created properly in the router - 22, 3335, 5900, 8001). Interesting thing that VNC viewer is working properly without any issues. Have you ever encountered such an error? Do you have any idea to solve it? Thanks!

Hi guys, since I have upgraded my iPhone to iOS15 remote operator does not work. It is interesting because it works if I connected to wifi internet but it isn't if I try connect via 4G. Do you have any perception of it? Mobile Data and Local Network are also allowed in settings

Hi! In my current project I need a little help from you guys! In one part of the project I need to control 216 outputs at the same time with a bit high frequency. ( Now, it's a working machine with Mitsubishi PLC, I have to replace it with unistream for other reason. By the way, the mitsubishi PLC has normal (no pwm) transistor outputs and a basic CPU model.) The requested frequency is 200Hz 20-45% DC. Now, I can reach 70-80Hz besides 5-6ms of PLC cycle time. In VisiLogic there is an opportunity called Write Output Immediately. Is it exists in UniLogic? Or it would be another option to reach 2ms wide impulses on outputs at lower frequency It is not acceptable to use UID-0808THS (200 PWM outputs non sense). Any idea? My PLC-s: USP-156-B10 UID-W1616Ts and lots of UID-0016Ts

Hi, I have the same issue. Latest firmware, latest U90, run as admin, compatibility.... How to solve it? Error appers when I click to favorites icon

I've just done forced update. Did not solve the trends problem

Wow! High five!

Hi! Is there any option to increase VNC resulition size? I'm using Real VNC viewer and all of the Unistream PLC I've added have 800x480 resulition. Also the same (800x480) resulition when I'm using USP-156 which has 1366x768 resulition. It causes poor view on VNC. Any experiences with 15,6" and VNC?

Hi Louis, I'm using UniLogic V 1.29.111 and I have the latest firmware. How do you mean to forcing an update? Need to start the procedure again? I'm just doing some logic to send emails. What are the issues?

Sorry for my late! I was on a new project launch and I didn't have any freetime either energy to reply 🙂 Yes, I've inserted SD card. This is the first step after unboxing (it is necessary to update firmware what is my step 2) By the way I've just noticed a strange thing: is that normal if Sample Interval value equel to 0 in spite of that I set it to 10 seconds at the data sampler preferences? You can check it in this print screen: (You can also see the live values of the analog inputs) I'm also attach the project file! Trend.rar

I've tried severel values without any differences. °C units = Thermocouple with current transmitter 0-1000 °C 4-20mA Pa units = Differencial pressure transmitter 0-1500Pa 4-20mA Yes, the values are linked to analog inputs with live values. It is a working system and I still don't understand why it happens 🙂 despite of I've done severel unistream projects with trends, data tables, email and so on. I am confused now

UniLogic V1.29.111 USP-156-B10 I'm sorry it is not allowed to send my project file. However I've some USP-070 PLC in stock, I'll try trends on it and send some news

As you can see MIN value is 0, MAX value is 1000

Hi! First of all I'm attaching a photo: Why are the max values equals to 1? All the curves format settings are equal and all of these are INT16. What a hack am I doing wrong??? Please let me know before I freaking out 🙂

Thanks! I'm looking forward it!