Search the Community
Showing results for tags 'jazz2'.
Found 4 results
Hi. I have a Unitronics JZ20-R16 (Jazz2) controller I’ve programmed to run a simple air ventilation system in my house (The thing is running great btw.). I also have a self made Arduino based data logger (I use it to monitor and log my energy consumption, temperature, etc.) I’m not building those things or mass producing, Arduino electronics is my hobby - I just use it to stay sharp. So I decided to cross-integrate my air vent. Controller with my data logging unit (I want to see the status of my air vent. Controller unit on Arduino). So for starters the task is to simply send a 16bit int to Arduino and receive another 16bit int from the Arduino. The communication protocol of the choice was MODBUS through RS232 interface (as I already have MJ20-PRG; MJ20-CB200 and a MJ10-22-CS10). I’ve decided to use JZ20-R16 as a Master (Arduino as a Slave) in a 9600 baud 8N1 configuration (default for JZ20-R16). For Arduino’s RS232 interface I’ve used TTL-RS232 converter (MAX3232 based) : Experiment 1: In order to see if the Arduino’s MODBUS feature is working I’ve connected Arduino to my PC using the given connector and a RS232-USB converter. Arduino was configured as a slave and ModbusPoll software (http://www.modbustools.com/modbus_poll.html) simulated a master. I was able to both read a holding register from Arduino (03) and also write a register (06). Those are the desired options. Experiment 2: In order to see how MODBUS is working on JZ20-R16 I’ve hooked it up to my PC using my MJ20-PRG; MJ20-CB200 and a MJ10-22-CS10 later connected to RS232-USB converter. I’ve uploaded a program (by pressing buttons 1 and 4 I send an int or correspondingly request an int from slave): (see in uploaded files) It make the JZ20-R16 work as a Modbus master on a RS232 interface. In order to simulate a slave I’ve used ModbusSlave software (http://www.modbustools.com/modbus_slave.html) . Once again, the combination worked perfectly. Once again all the required commands worked. Here’s the photo of my hookup: Then I’ve noticed a possible cause for future problems : lines 4 and 7 of my MJ10-22-CS10 are actually used in this communication. It turned out that the RS232 communication with JZ20-R16 require 6 wire communication instead of 3 wire communication I’ve expected from RS232 interface. Due to the requirement of RTS and DTR signals! I’ve turned on my scope and actually saw those signals on pins 4 and 7 of MJ10-22-CS10 connector going high after the “handshaking” with my slave simulator was done. With PC USB disconnected: PC USB Connected: MudbusSlave after “handshaking”: Successful communication: CH3/4 are the DTR and DTS signals correspondingly. At this point I’ve realizes that sue to those signals I would not be able to connect my Unitronics to my Arduino, as the TTL-RS232 connector simply do not support DTR and DTS signals. So after hooking up my Arduino to Unitronics I see the following on the scope: Both DTR and DTS signals are on 0 instead of HIGH, which prevents the JZ20-R16 from accessing the modbus. The questions: Is there any chance to make JZ20-R16 communicate over RS232 without use of DTR/DTS signals? Is there an option to tweak those signals (connecting them to +5V permanently) Use of other TTL-RS232 converter? Any other way to make Arduino and JZ20-R16 communicate over RS232 interface using MODBUS Thank you for the patience. samplemodbusmaster232.U90
Hi, I am facing troubles while trying to log and later display time using Jazz2 controller. So, I'm trying to make an error log. When the error occurs I store current content of SI31 (RTC time) to MI (MI33 in this case - so far it's working). Then in order to display the error I pass MI33 content to MI41 (MI41 is linked to Time Function variable (in CT format) that is then displayed on HMI) . You can see the whole process in images below. The problem is that in the end, the content of MI41 (decimal 1500 - which I corresponds to 15:00 time) is then displayed as 05:DC on the HMI display. I guess the problem is caused due to DEC/HEX conversion. Any idea how to fix this ? Thank You.
Hi, I have a JAZZ2 PLC(JZ20-JT40) with OS V2.35(B08) and with ethernet addon(MJ20-ET1). The plc comes with 2.36 OS but, I have to reflash it because its totally crashed somehow. I can't start it. I am able to connect with the programmer software(V6.6.6 latest). I want to acces to the plc by modbus communication. I set up the sample program by the instructions on the help topic. The modbus topic is shows that, I must store some values to SI. I attached the screen of the sample program. I think the SI values displays weird values. What do I wrong? Thank You
Hello, We have a problem with Unitronics Jazz 2 series PLCs (JZ20-R31, +adapters MJ20-RS) trying to connect to modbus communication line. The problem is we cant initializate RS-485 com port, every configuration are restored to factory default (9600;7;1;even;n) after RS-485 cable connection to PLC and in system menu it is impossible to change communication parameters if RS-485 cable is connected (RS-232 com port we do not use). We do not have any problems with Jazz 1 series plcs using almost same program, same configuration. + U90 ladder we are using last version (v6.4.9) + Unitronics 2 series OS is last version (V2.30 (B08)) + Communication line is good (we checked). + We have two Jazz 2 series plcs with same problem. P.S sorry for my english.