Jump to content
bobnorway

New Engineers and Standards

Recommended Posts

Standards

Once apon a time in the 'good old days' there was a standard to ease interfacing of different equipment together.
It was called 'RS-232' for simple and effective serial interfacing.
The voltage was a given always a -12 to +12 volt swing, a safe voltage with reasonable noise immunity.
Then one fine day in order to reduce parts count it was implemented as 0 to +12 volt.
Still almost as good and cheaper.
As terminals became PC's the parts count was reduced so the readily available 0 to +5 volt
 was used as a power source.
Not quite as good but even less expensive.
The lower voltage allowed for a higher communication speed.
Sometimes one end of the Com line was one type and the other was a different type.
This lead to problems but neither end manufacturer was 'responsible' so it continued on.
The Standard called for a 25 pin 'D' sub connector allowing for plenty of future space.
This configuration gave full hardware hand shaking, these hardware lines could be tied
 up or down to reduce the parts count.
Tied lines were not as good but are even less expensive.
With the reduced pin count it was possible to use a 9 pin 'D' sub connector.
This reduced cost and space requirements.
Luckily throughout all of this development there has always remained a 'constant'
 which is one 'transmit', one 'receive' and one 'ground' pin.
Within the Standard 25 pin version pin 2 TX, 3 RX, 7 Gnd are used.
Of course the Standard 9 pin version is different 2 RX, 3 TX, 5 Gnd.
The 6 additional handshaking lines are also moved around.
These are the 'Terminal' standards, the other end is a 'Modem' standard with 
 the functions of pin 2 and 3 reversed.
Naturally if it is for a PC to PC Com line this will not work and the infamous 'Null Modem'
 crossed cable is used.
PC's are often supplied with male connectors which may require a female - female adapter.
Often a male - male adapter will also be necessary and a 25 to 9 pin adapter is very usefull
 to complete the connection.
A break out box is a very handy tool allowing individual pins to crossed as required until
 the connection works.
In real life sometimes one or more of the pins are accidentally left floating this gives
 all sorts of intermittant trouble.
Grounding two electrical machines together via the serial connector sometimes produces
 a ground loop which plays havoc with the system.
To avoid this danger some manufactures don't connect the ground pin to the chassis!
The original 'standard' had a cable shielding connection to the connecter shell but
 inexpensive connectors made of plastic defeated this function.
 
So the 'RS-232' Standard implementation can be 25 or 9 pin, male or female, 12 or 5 volt,
 send or receive function, handshake or not, grounded or isolated.
I should mention 'Standard' speeds, baud rate (bit) 50 and upwards, 
 Mark and Space (1 and 0), Start and Stop bits, 5 to 16 bit per character, '
 Standard' character coding, check sum controls, Com protocols, point to point or multi drop.
So it may take a while to get a 'Standard' system online.

a good read http://www.machine-information-systems.com/RS232_Pinouts.html
and also https://en.wikipedia.org/wiki/RS-232

Regards
Bob Clarke
 

Share this post


Link to post
Share on other sites

You should also mention the different types of USB to RS232 adapters,

choosing the right driver for them, and applying the "unnatural" power for some interfaces (like Jazz PRG) from the transmission lines.

Galvanic isolation for the adapters,  the quality and length of the cables.


So still on the shelf I have from

13 hours ago, bobnorway said:

'good old days'

DOS3.0, DOS 5.0, DOS 6.22, Win95, Win98 computers with hardware RS232 and the correct Standard.

Big Box with different connection cables and adapters also present.

And it is not museum :).

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...