Jump to content

sgull

Members
  • Content Count

    196
  • Joined

  • Last visited

  • Days Won

    10

sgull last won the day on December 24 2018

sgull had the most liked content!

Community Reputation

13 Good

About sgull

  • Rank
    UniGuru
  • Birthday 01/24/1968

Profile Information

  • Gender
    Male

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. That is a video I would definitely watch. The chiefs at Unitronics should jump at this offer. would make a great training presentation for all levels of user.
  2. When you are setting up a display, select numeric elements on the right hand side. Here you can assign an IP address or IP settings box that the user can use to modify addresses
  3. Thanks Aus/Joe Hi Aus - yes I did the repair via the system restore. I had a recent backup done and tried this first but it failed. Joe - I have followed the steps you suggest. File downloaded with no problems. Thanks for the help
  4. Hi Not really related to this topic, but related to downloading the file. I use Firefox browser. When I tried to download the file above and selected to save it to disk, the file appears to download but after a few seconds windows crashes. This happened twice before on another laptop, however this is a new laptop and it happens again. Windows explorer keeps trying to restart every second so I cant troubleshoot anything. The only way to get back working is to restore from a backup or do a system restore. Any ideas if this is a Windows, Firefox, Unirtonics or j
  5. I think this should be a message on the header of all posts. For example I get a default message when I post stating the following "Your content will need to be approved by a moderator". Many new posters get frustrated when their post is not posted, read or solved immediately, not realizing that this is a voluntary forum. When people try to post there should be a message advising them of this and also if they would like to also send to the official UNITRONICS support. It would be easy for the forum designers to include this than everyone needing to set up their individual m
  6. Hi I think the unit is listed in the remote I/O user manual. Try this link https://www.unitronicsplc.com/wp-content/uploads/2020/06/UniStream-Remote-I-O-User-Manual.pdf
  7. Hi KVJ When you have a situation like this where you do not know if the program is the same and if you do a download there is no way to go back you should consider the following. A V570 PLC is not a very expensive unit. If you convince your customer to invest in a spare unit, you can try the new program in that unit and see if it behaves as expected. If it does not work, just put the old PLC back. Regards Denis
  8. Hi Put the DOK into your PC Connect to PLC with ethernet cable In UNISTREAM click on "UNISTREAM MANAGEMENT" and then "REMOTE UPDATE" Half way down the window that pops up select DOK as the "target drive" Click on "UPDATE" at the bottom of the window and the PLC should be updated with the latest version.
  9. Hi On your initial post you mention that you can ping the PLC. Even though you cant go online because of a firmware mismatch, you should still be able to use the remote update function. You dont need the SD Suite just a blank SD card. Its possible that a USB stick in the PLC will also accept the files. Regards Denis
  10. Hi If you can communicate with the PLC over ethernet then you should be able to update using the remote update option. You will need an SD card in the PLC in order to accept the download files.
  11. Thanks NoamM I will upgrade to the latest version the next time I am on site. I can see the "clear alarms" bit in "ACTIONS" but this only clears all active alarms. Is there a bit I can set to clear the alarm history? Normally after commissioning and testing a system I have many alarms that I have tested. I dont want the customer to see these alarms or he will think the unit has had major problems. Forget the second part - i found the location of the clear button in the properties window. Regards Denis
  12. Hi Alex Thanks for your reply. The unit is on site and has been running for a year. This is the only issue I can see. I dont like upgrading the software on a unit that is working unless I have a good reason to do so. It is difficult to get downtime on the machine and they normally give me a very small window for modifications. Do you know if this is a known issue with 1.28.34 that has been solved with later versions? Also is there any way to completely wipe the alarm history? Regards Denis
  13. Hi All I have a unistream 10.4" PLC+HMI. I am using program version 1.28.34 I am using the built in alarm function and also using the alarm history. The problem is that when an alarm occurs it does not always get added to the top of the alarm history list. I have set the view to default by date. I am using the date format dd/mm/yy If i get a new alarm it sometimes appears on top of the list or sometimes if I scroll down it will be in the middle of the alarm history. Does anyone know if this is a known issue with this program version. I dont want to upgra
  14. Thanks NoamM When is the expected release date for Version 30
  15. Where did you get 1.29.145? the latest version appears to be 1.29.111
×
×
  • Create New...