[PID regulace with temperature - example]

Why value Control value is equal to the output high limit?

This value should be changed yet?

Why has not changed and is still there up to a minimum or maximum?

[PID regulace with temperature - example]

for set:

Set clue 900

Process Values 950

Proportional band 1

integral time 20

derivative time 5

sample time 10 000

input low limit 895

high input LMIT 905

ouput low limit -10

output high limit 10

reverse action 0

pid mode 0

control value 0

status -6

autotune done 0

control value proportional 0

control integral value 0

control value derivative 0

integral eror 0

[Control valve with 4-20mA output]

Thank you all for your answers.

 

Maybe I do not understand.

Scale same?

You think that corresponds to the measured temperature is real? This would be conform by other measuring devices.

I do not know how to set those values.

I would need to show how well these 19 values ​​set.

Then I'll understand what I'm doing wrong.

And in the future, I am already set up himself. Help helped me :-(.

 

 

for set(For temperature 900+-9):

Set clue                                                                  900

Process Values                                                      950                                          

Proportional band                                                  1 

integral time                                                           20                                                                                           

derivative time                                                        5

sample time                                                           10000                             

input low limit                                                          895                                     

high input LMIT                                                     905                                              

ouput low limit                                                        -10                                                 

output high limit                                                    10       

reverse action                                                       0      

pid mode                                                              0

control value                                                         0                                                        

status                                                                   -6

autotune done                                                       0

control value proportional                                      0

control integral value                                             0

control value derivative                                         0

integral eror                                                          0

 

Process Values is input temperature.

[PID regulace with temperature - example]

Hi, 

 

i have problem with my example for PID regulace with temperature,

(PID-With UISPT4 module-UniStream_070_PID_UISPT4.ulpr)

i know not, like i set parametrs for PID for PID_confing.

 

I want to set temperature 90°C +- 0,5°C.

 

Please, can you advise for set the 19 parametrs.

 

Because coils are either just patches and topi or off.

Control does not take place

i will know then like i will set parametrs for future :-)  

 

Thank you for answer.

[Chart-figure-trend]

Hello,

 

I do not know what I'm doing wrong, but the chart is plotted.

Example: UniStream_070_XY_Trend.

Load it into the PLC.

Porměné in PLC running, I can see raising and lowering setting values.

I do not know what to do ..

This will probably be a trivial matter, but I can not see it.

----------------------------------------

UniLogic Version 1.13. Rev.9

 

[CPU does not count]

Thank you for your answers,

 

I sent it to support, support resolved through remote management. (He worked on the problem for about 2 hours)

I wrote to him about the details so that he wrote to me about what the fault was.

Unfortunately already written off.

[CPU does not count]

Hello

 

I have a problem with the software.

After programming screens (graphics).

I started to program on the logical part.

None of the logical internal calculations.

But the touch screen can change the variables, when I look into wacth.

I can jump from screen to screen.

 

 

As shown in the figures.

the first part of example should add up whole period and in the second part should be attributed solely in response to the key pressed.

 

If I post the finished examples of websites Unitronics and behave exactly the same variables ragout touch on the screen, but there is no internal calculations.

 

Thank you for answer.

 

 

http://www.imghosting.cz/view-34Buton_0.png

http://www.imghosting.cz/view-94Button_1.png

[During the update, I fell on the power.]

Yes, I am.

Thanks for the advice issue has been resolved.

[Windous 8]

Thank you for the advice

[Invalid user application]

Thank you for the advice

[Upload controller]

The project in the controller cannot be uploaded unitronics

This is because the project was downloaded without an upload option

 

 

Thnak you answer.

[Invalid user application]

How can I solve this problem?

 

 

USP-070-B10

USC-P-B10

 

 

unistream firware upgrade

your firmware is up to date

no upgrade is need

 

 

invalid user application

 

the controller does not contain a valid application.

this may be due to a corrupted application or version mismatch

 

 

check that you are using the most recent unilogic software and unistream firware version, verify com settings perform download all

 

if problem repeats, please contact support

[During the update, I fell on the power.]

Hi,

 

During the update, I fell on the power.

Where can I find the upgrade to USP- 070-B10. I do not have the correct version

 

[Windous 8]

Hi,

 

I have windous 8, but only http://www.unitronics.com/W7 drivers.

The problem may be in the windows?

 

The PC-PLC Comunikace - It writes PLC update needed for Ethernet (yellow triangle with an exclamation mark)

 

 

This operation cannot be completed until the controller OS is updated. Either: Update the files: connect a USB stick to this PC and press Copy to USB Stick to copy files, and then use the USB stick to update the controller. or prees cancel to stop download

update needed.