Search the Community
Showing results for tags 'modbus tcp'.
-
Does anyone have experience with the BacNet gateway? I can't seem to establish a Modbus session from my V1210. PLC is connecting on port 502, socket 2(Client/Master) to the gateway's port 502, socket 9(Server/Slave). I've done a packet trace and found a Modbus/TCP error 'Cannot classify packet type' Attached is the tcpDump, Modbus comms config in visilogic, and gateway config file. Someone, please help!!! Thank you in advance tcpDump.pcap Modbus_BacNet.vlp Synthex BacNet Gateway Config.csv
-
Hello, I'm trying to use V700 as master and two lexium mdrive motors as clients through MODBUS/TCP. I set up the function blocks per example "V700_Modbus_TCP_master.vlp". I can get the motors to connect with V700 but once i write modbus commands to motors i get no motion. one of the examaples for requesting commad is mentioned below as modbus tcp commad for the motor to move at slew speed of 600000 micrsteps/sec. Please take a look at the code and let me know what i'm doing wrong. Also please let me know if you need more information. Thank you in advance for the response.
-
Hi I am trying to connect a 350 PLC with Inductive Automation's Ignition SCADA using Ignition's Modbus TCP driver. The PLC program image is attached. I do get a connection established in the Ignition software to the PLC but I can't read any tags. The following are all the settings I have in the Ignition SCADA I have tried Ignition's Modbus TCP, Ignition's Modbus RTU over TCP, Kepware's Modbus TCP driver all to no avail. I already have 2 other PLCs connected to
- 5 replies
-
- scada
- modbus tcp
-
(and 1 more)
Tagged with:
-
Hi, I'm using a Samba 3.5 with ethernet card to send data to scada system. With test purposes I'm trying to send a discrete input MB 0 in response to the read digital input command (0x02) with the following instruction: But in the test software (Simply Modbus TCP Client) I can't see the value of MB0. Trying to find the answer, I tested sending the MI10 value in response to read holding registers command, but It doesn't work neither. I'm using the modbus TCP initial setup from the examples and the webinars, and I can see the connection in the Samba, but I can't send th
-
Does anybody know if Vision controllers (ie V130) support Modbus TCP or do they support the Modbus RTU over TCP implementation. The difference is that the first follows the original Modbus TCP frames (ie no CRC) while the latter encapsulates the serial RTU framing sent over TCP media. Which one is supported by Vision and the other Unitronics controllers?
- 5 replies
-
- modbus
- modbus tcp
-
(and 3 more)
Tagged with:
-
Hi! My name is Arnor and I am from Iceland I am trying to establish connection between two Vision PLC's. I have the master: V700 and V350 as slave. I can use SCADA pc software to connect to the slave and read the data. But I am not able to read data from slave to V700. I added both programs to google drive folder (sorry, the programs was to large, and its a bit mesh): https://drive.google.com/open?id=1yL1h1ZvJomBeoY7v22UvHVeY09T4ooAC I am using also Serial modbus on both sides that works well. The PLC are set up like this: V700: 192.168.1.20 V350:
-
Good day, Due to lack of ethernet sockets (v570) we need to set up modbus TCP communication with 2 Omron PLC's through the same socket. When connecting separately all works fine, but can't figure out principle to get them work together.. Tried different ways: after configuration, there is command to connect socket to one of PLC's IP (indirect IP and port), then after some time there is command to close socket and to connect to another IP. Nothing happens, conection to only one IP. Maybe something wrong with timing or connect socket commands. Maybe someone could share working example how to
-
Hi, I have a problem with ethernet-connection, the PLC is V1040 with V200-19-ET1 -ethernet card. I've been using ethernet-connection with Samba (Modbus TCP connection to SCADA software) and it worked fine! The problem is, that when I plug ethernet cable from v1040 to ethernet switch, switch seems to have no activity. Not even Link/act -leds doesn't turn on. When I keep touch screen pressed and enter setup, it show MAC address and IP of ET1, so PLC recognizes that there's ethernet card installed. I've been trying another PLC and another V200-19-ET1, different ethernet switch, di