[HMI picture of your creation]

I would like to know if you can show me you HMI display with Vision that you created. I need some idea to create new project with the V700. I upload somes displays that I created first time with the V350 for somes projects. Thanks

 

 

 

 

 

[High speed counter]

I have 5 preset for this cable winder. 

1) Slow down before stop

2) Stop the line at XX feet

3) Send a output pulse to the printer at 1/4 of length for cable identification

4) Send a output pulse to the printer at 1/2 of length  for cable identification

5) Send a output pulse to the printer at 3/4 of length for cable identification

Can I use the compare box (greater equal) to compare the length with a preset and output on when he reach the preset? The operator run the line at 400 to 1000ft/min.

The plc will be fast enough to send a output at the good preset of length?

My program has 25 rungs and when I test and go online with my laptop I see on SI0: 2. 

[High speed counter]

How  configure the HMI to see the speed in Feet/min.?  In the hardware configuration I setup I1 to Frequency measurement 1000mSec in ML 1. (I0 is configurated Shaft encoder X4). How convert frequency to feet/min.?

When the encoder turn one time is 1 feet. Encoder is a 100ppr, Thanks

[High speed counter]

Thanks

[High speed counter]

I have a Durant counter that I want replace by a V350-35-T38 because I need 4 preset. In the setup of Durant counter we have to enter count scale. I don't see how put this number in visilogic software. My encoder is a quadrature 100 ppi.

[Feet per minute with proximity switch]

I have a M91-2-R1. How can we measure the speed of my conveyor with proximity switch. The conveyor go to approx 8 feet/min. and the sensor detect at all 1 feet.

[Replace Fusion Durant counter by M91-2-R1]

DC drive with dc motor

[Replace Fusion Durant counter by M91-2-R1]

I have a M91-2-R1 to make some test. I want replace Fusion counter by the plc for a winder. The counter have a encoder 100PPR. When the count reach Preset 1 the motor jog at X speed and when he reach the preset 2 he stop the motor for cutting the material. In the U90 software the are samples of HSC. But I don't see where can I put the number of PPR of the encoder?

[ziplink]

Can we have a ziplink like : http://www.automationdirect.com/adc/Shopping/Catalog/Programmable_Controllers/CLICK_Series_PLCs_(Stackable_Micro_Brick)/ZipLink_Wiring_Solutions/ZL-RTB20

 

for cable a control box with many push button for the plc input?

[V350 with e-mail and ethernet]

Works perfectly!

[V350 with e-mail and ethernet]

Do I need two differents local port number? 

[V350 with e-mail and ethernet]

I have a V350 with ethernet card. I setup a counter for the maintenance. I send a e-mail when the plc reach the counter. Work great. Also I would like control the plc with Remote Access? I try but don't work. For e-mail I setup the block ''TCP/IP - Socket init'' Master. But I can't connect to plc whith Remote acces when I configure with e-mail.

Thanks. Can I send e-mail and use Remote Access?

[RS232 cable]

Thanks you for the explanation!

[RS232 cable]

I have a M91 into a box. I would like to have a acces to the RS232 port for troubleshooting whithout open the box. I connect the cable to a coupler like that: (http://www.digikey.ca/product-search/en?x=0&y=0〈=en&site=ca&KeyWords=a34359-nd) but the plc don't want communicate. I check the continuity for both cables and is ok. I there a maximum length for rs232? When I plug the plc direct to the pc with one cable is ok. When I connect two cable with the coupler don't work.

Thanks

 

[Flyback diode]

Thank you!

[Flyback diode]

Should I use flyback diode on output with my M91-2-T1? I will drive Solenoïde valve with on-off at 2 secondes of interval.

Thanks!

[Disconnect switch]

Which safe distance should place the master disconnect switch( 20A) above my V350 PLC? 

I don't want problem.

Thanks

[M91 Ethernet Communication]

I add a serial to Ethernet converter to one of my M91 and works great! For only 130$ Brainboxes ES-246

[Encoder and position with vision plc]

If you were to put the encoder on the output shaft of the gearbox your maximum frequency will be 614 Hz, which will work fine. Can you do this? Yes

I will slow motor down. I will make a test with a m91 spare before!

[Encoder and position with vision plc]

The PPR is 2048 because I need a precision stop load about 1/4 inch. The rotation of the encoder will be 1500 to 1800 rpm. The encoder will be mounting on the motor. The motor is a 1800 rpm and the ratio gearbox is 100:1. The gearbox is a allow shaft.

I will try with a M91 spare unit for the moment! It will be the same program setup on Vision plc?

Thanks

[Encoder and position with vision plc]

I have a new project that want to use Vision plc. I don't know if I can plug a incremental encoder HS35R with Z (homing). I have a motor with drive and gearbox who connected on the load. The load rotate clock wise but need to stop at 4 positions that the operator enter in the hmi. I would like to know if the vision plc can control a drive with HS35R encoder with Z (homing) for position?

Thanks

[M91-2-R1]

I have a M91-2-R1 to control 2 heatgun and 2 exair cooling vortex tube. I use 120Vac scr to start the heatgun and 120Vac solénoïde valve for the cooling. Do I need a RC supressor or other protection for the contact of the plc?

The cycle is

1. turn ON heater 7 sec. turn OFF heater and start cooling 7 sec. turn OFF cooling

2. turn ON heater 7 sec. turn OFF heater and start cooling 7 sec. turn OFF cooling

3. turn ON heater 30 sec. turn OFF heater

We make this cycle 7 hours per day.

Now I have a one bad contact relay.

The M91-2-R1 is the best to control scr and solenoide valve?

I chose this plc because I have a department that use 52 of this plc.

Thanks!

[M91-2-R1]

I bought a new plc M91-2-R1. I put the new plc ON after 1.5 years after purchase. The plc go ON and dead and smell burning. I get out this one and put another and work great. I open the dead plc and you can see on pictures the state of the boards.

http://img.photobuck...lc/DSC09425.jpg

http://img.photobuck...lc/DSC09427.jpg

http://img.photobuck...lc/DSC09430.jpg

http://img.photobuck...lc/DSC09422.jpg

What do you think?

Can I return the product?

Thanks

[set timer via analogue input]

When implementing a timer throught the HMI and assign a timer operand to the variable . Can I block the maximum seconde for the operator can't go over?

[set timer via analogue input]

I would like to know with the M91 if can I use a potentiometer plug into the analogue input (0-10V) to setup the time of a timer?

Thanks