V700
-
Posts
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Blogs
Downloads
Articles
Media Demo
Posts posted by V700
-
-
Serial connection through micro usb cable.
I downloaded the same program from the same pc to an old hmi V700 that I have in my test bench that is more than 5 years old and is working fine.
I believe there’s a conflict between the program version and the o/s of the screen.Visilogic version now: 9.9.00
Program creation version: 9:8:90
Latest saved version:9:8:96
O/S version: 4.12 (38)
-
Battery voltage 3.3V ✅
Download ✅
Download All&Burn ✅
Set time and date from pc ✅
I will try the SB8.
In one of the hmi’s that I tried to load the program, update of the O.S was needed but not in the second one.
It’s a little bit weird that both of them have the same issue, so I think there’s something wrong with the downloading procedure.Do I need the latest version of Visilogic maybe?
-
-
Hi guys!
I want to control a vfd with an analog signal 0-10V.
The program is running on 2 phases, in the first phase i measure with my voltage meter the right value in the analog output, in the second phase i want the speed to change so i load a new value through the MI.Although that the new value is shown in the monitor, my voltage meter shows me the same voltage. -
Yes i changed MI to ML and it works. Thank you!
-
I use a bargraph in my project that is linked to a timer.(TD1)
I set bargraph's max value using an MI which has the preset value of (TD1).
when the timer takes values > 00:05:27 the bargraph does not work at all
when the timer takes values >00:11:10 it works only for some seconds,
when i run the simulation i see at the preset value MI a small value, i think it has to do with the overflow,
it works only at 0 to +32767
what operand should i use to fit max time of a timer(99h) ?
-
-
I have a V700.
When i press the button once it increments by one,
but when i press and hold the button i want the value to continuosly increment till I let go of the button.Any idea how to do it?
-
-
My connection was wrong...
i tested with ice-cubes and it was close to 103 ohms.
thank you for helping!
-
Yes. I connect it to analog input 0
5A 4A 3B
-
I also have V700 with snap i /o v200-18-e3 / 4 xb
i connect a 3-wire PT-100 and place the input in MI operand (C), the value i get is about 5370. I measure the resistance from the PT-100 to 120 Ohms so according to pt-100 table it has to be about 50C(the temperature in my room is 22C,maybe the sensor is not good).
I divide 5370 with 100(no 10 as mentioned in the last post) so i get 53C. Is that correct? -
ok!
I supply voltage to 0V and V1 and it worked.
Thank you. -
Thanks both for replying!
This is my wiring.
So i keep it like this and just add 0v to 0V and 24v to V1? -
I use a V700 with V200-18-E3XB module.
I connect some switches to the digital inputs that work fine and some leds to the digital outputs so i can test my project.
I connect them according to snap in I/O manual pdfbut i have no voltage on the outputs
although in the program the output bits goes high.
Any idea what the problem might be? -
Thank you!
-
Thanks for reply!
I want time to be >=00:00:05
How can i put the timer value that the user gave in input A ?
-
Same problem here.
Flex727 can you explain it in more detail please?
Thank you.
V700 LOSES THE PROGRAM AFTER RESTART
in Vision & Samba PLC + HMI Controllers & VisiLogic Software
Posted
I changed both batteries and everything works fine.
I tried the old version of the visilogic and the new one and both execute the download.
Thanks to all of you!