Antal
-
Posts
41 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Blogs
Downloads
Articles
Media Demo
Posts posted by Antal
-
-
-
Hi
I have the solution. I made it your home screen, so it won't let you delete it.
Greetings Antal
- 1
-
-
Thank you very much for your reply. I understood now.
Regards B.A.
-
Hi, kratmel
Thanks for the answer. A transformer is required because all controls and contactors operate on 110 V AC. The question is if i connect the Neutral and ground the way i drawed the PLC will not demaged? This is the original drawing, this is what I want to control with a PLC.
Thank you in advance for your help.
Regards B.A.
-
Hi Ausman
I understand what you're saying.
This is an irrigation system in the fields, there are only 3 phases here neurtal NO. They made zero from the ground. This will not be a problem for the PLC?
Thank you in advance for your help.
Regards B.A.
-
Hi
I need help.
It can be connected in this way and nothing is damaged?
Thank you in advance for your help.
Regards B.A.
-
Hi
Thanks for the reply.
I sent it.
Greetings B.A.
-
Hi all.
USC-B10-B1, UIS-WCB1, UID-0808R,HMI USL-070-B05 or USC-B5-B1, UIS-WCB1, UID-0808R, HMI USL-070-B05.
Everything works fine as long as I load 4 programs on the PLC, this image is displayed after every 5th program upload. The image will be small. This error is present in someone else. Reboot and works again for up to 4 uploads.
There is a solution to this error.
Greetings B.A.
-
Hello Ausman
I thought writing on the table was harder to read and went easily. I got stuck with a simple solution. But this forum is good for people to help each other.
Sorry for my bad english.
Greetings B.A.
-
Hi Joe T
Thank you very much for your quick reply.
Works perfectly. I read the schedule from a table. When the time is the same, in one of the rows on the Table, the output turns on.
I need 20 different schedules a day.
Greetings B.A.
-
-
Ausman
I read what is on the link. Thanks for the good advice.
Regards B.A
-
-
Hello
Support don't answer, I need help.
USC-B10-B1 so far i have used version 1.30.62 Unitronics UniLogic everything is fine.I downloaded version 1.31.106 today. This error occurs several times after each update, not even the PLC goes.This is an error message.I put back the old version it works fine.Thank you in advance for your answer.Regards B.A -
I made a separate website.
IP: xxx.xxx.xxx.xxx/Module2/Info,based on the description you wrote,so it works perfectly.
Thanks for the help.
Regards B.A.
-
Hi
I need help.
PLC: USC-B10-B1
The website working only with full access? The user can only watch, there is an option.
Where can I find your setting for viewing only?
Thank you in advance for your help.
Regards B.A.
-
Thanks for the help.
Greetings B.A
-
Hi
I looked at the forum but i can't find a solution anywhere.
Web VNC works on the LAN connection. I want to use it via the web.
I have a fixed IP address. I want to use mobile and tablet.
I ask for help in solving it.
Greetings B.A
-
-
Hi
It was my fault. PCL and HMI
Greetings B.A.
-
Hi
Thank you for your answer.
I understood how adding numbers works, I did a little example.
Regards B.A.
-
Hi Ausman
Thank you for your answer
Sorry for the bad english.
I can do this to calculate, divide by minutes, or seconds, or hours etc. I can't add the measured results to get the total.
example
12+25+35+45=117-total
Regards B.A.
-
Hi
4-20ma is the incoming signal, flow measuring device, the data is there just i can't add them up, the total amount of fluid flowing through the meter per day / month.
Thanks in advance for your help.
Regards B.A.
How do I resolve this warning message?
in UniLogic Software
Posted
Thanks for the reply.
Unfortunately, this is the case. The Software is running without error.
Greetings Antal