Martin1
-
Posts
18 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Events
Blogs
Downloads
Articles
Media Demo
Posts posted by Martin1
-
-
I am looking to store a UINT array into a INT array. Is there a simple way to do this?
I am displaying my Analog inputs to a Data Table but my remote URB island inputs are in UINT format.
Anyone know a simple solution?
-
When I create a array[100], I would like to rename the tagnames. Is it possible to import from excel?
I do not see a easy solution.
-
Hi,
I have a v570 that is communicating with a Wonderware Intouch SCADA computer.
I want to be able to read/write MF tags to and from both devices.
When I write a value of 1.23 from SCADA, the v570 reads it back as 4.066596E+29.
This was tested using MF0 using value "416385 F" in Intouch.
Is there a way of displaying the MF value directly?
-
Hi Flex,
I tried that but unfortunatly no luck.
I can read ML's using address 428673 L in Intouch.
-
On 12/5/2012 at 11:43 AM, Steelman63rus said:
In DASMBTCP configuration set:
Maximum Outstanding Messages = 1
Register Size = 6
Addressing:
MF0 - 416385 F
MF1 - 416387 F
MF2 - 416389 F
....
Hi all,
I know this is an old thread but I am trying to read an MF register from a v570 PLC.
When I try and read MF0 from "416385 F" I do not get any response from the PLC.
I am reading ML registers just fine.
Some help would be greatly appreciated.
-
The v350 would need to have a ethernet card installed and linked to a router with a static IP to access the PLC
-
-
Hi all,
I know in unilogic there is a way to remove unused tags but is it possible to do this in visilogic?
It would be a great feature when starting a new project from an existing one.
-
Are you using remote CanBus modules. If so, check the earthing. Make sure it is only earthed on one side. I had this issue before
-
Hello,
I'm looking to exchange data from a remotely located Vision130 to a either UniStream or v570 controller using GPRS. 2 Analogs & two digital signals. Is this possible?
Would there be any examples of such a setup?
Regards
-
Hi AZ1975,
Would it be possibe to send be your prog to me too? I too are having issues sending email.
Thanks
Martin
-
Hello,
Is it possible to put an extention cable in the SD slot? I need to access the SD slot without opening the panel door.
Also, is it possible to download/View trended data/graph form the SD card using SD Card Explorer via Com Port?
Thanks in advance!
-
Thank you for that. I can now save my projects:)
I was saving my projects to my dropbox folder with no problem but since I upgraded my PC it won't allow me any more.
I've had a similar error when trying to save a project into a folder that's nested too deep. If you're saving to a folder other than C:\Program Files\Unitronics\Unitronics VisiLogic_C\Applications\, then try saving the file there, or elsewhere that doesn't have too many sub-folders.
-
I am having an issue saving a project. Any time I go to save, it pops up error code 464 "illegal project name". What is causing this? I am not using any illegal characters!
I uninstalled visilogic twice but still the same:(
P.S
I recently got a new PC (X64bit)
-
Thanks very much Simon.
It's always the very small things that catch you out!
-
Hello all,
I am having an issue sending an sms alarm via Com Port 1 on a V130 on a enfora1308 modem.
I have done it before on a V570 and worked fine.
The Modem SB80 is High & the GSM signal quality is at 16.
When I press Key #9 on the Keypad it should send a test message.
I have attached the config below.
Could someone help me before I pull all my hair out!
Regards
Martin
-
David, if you have any questions, let me know. I can help
MQTT - Home Assistant
in MQTT
Posted
Has anyone setup a Unistream PLC to send/receive data from Home Assistant via Mosquitto broker?
MQTT explorer is registering the topic but the data is not displaying correctly.