SD Card Suite
Enhanced Vision OPLCs support SD cards that enable application data to be stored and remotely accessed.
SD Suite enables you to view and manipulate that data, as well as format cards and perform other tasks.
Note that SD Cards also enable , complex web-page hosting, and application cloning between OPLCs.
48 topics in this forum
-
- 10 replies
- 6.6k views
-
- 7 replies
- 2.5k views
-
- 0 replies
- 620 views
-
- 1 reply
- 517 views
-
- 5 replies
- 542 views
-
- 1 reply
- 1.2k views
-
- 5 replies
- 577 views
-
- 8 replies
- 710 views
-
- 3 replies
- 626 views
-
- 9 replies
- 1.8k views
-
- 2 replies
- 1.7k views
-
- 2 replies
- 1.2k views
-
- 4 replies
- 992 views
-
- 4 replies
- 6.7k views
-
- 3 replies
- 1.8k views
-
- 4 replies
- 3.1k views
-
- 0 replies
- 1.3k views
-
- 0 replies
- 1.2k views
-
- 5 replies
- 1.8k views
-
- 3 replies
- 1.7k views
-
- 2 replies
- 1.3k views
-
- 1 reply
- 2k views
-
- 1 reply
- 1.7k views
-
- 1 reply
- 2.1k views
-
- 6 replies
- 5.4k views
-
Member Statistics
7,184
Total Members1,206
Most Online
-
Topics
-
-
Who's Online (See full list)
-
Posts
-
There's another option - that I haven't personally tried, but should work - is to create a CLONE file on an SD card using VisiLogic and the correct firmware associated with that version of VisiLogic. Then load the clone on the PLC via INFO Mode. The PLC should then have the latest firmware and the program loaded. Of course, the OP has never volunteered the PLC model, so it may not have an SD card slot. -
Guus, my take on your post is that you got to the point shown by Micapp, and then the procedure failed. Is this correct? Take note of everything everyone else has said already, and please answer the questions asked. I have experienced issues that I haven't had time to resolve, with Windows versions upsetting the ability for the os update to run properly on my main PC. Points to note on this: 1). Depending on your plc model, to do the update you will likely be needing to be online through port 1, with the grey MJ10-22-CS25 cable linking the PC to the plc. At present the only way I can do this is with my W7 laptop that runs a dedicated serial port. Note that my main PC on W10 does have a native serial port, but Windows has done something to break the OS update process which used to be OK. 2). If you are using a USB to serial adapter, it must be a Prolific chip. One based on the FTDI chip does not work properly for some reason. Have a read of this topic. I don't know if the very last comment works or not. https://forum.unitronics.com/topic/500-updating-oplc-os-bin-lib-file-boot-file/?do=findComment&comment=2003 cheers, Aus -
You can download new OS under Connection - Install operating system Run Check. If the OS must be installed you will be guided in this window. You do not need to download anything else -
I have been able to get my project working somewhat and I have attached the latest ladder. With this setup I am able to get the counters to increment but it seems I am only getting about 10 percent of the pulses to register, With a ppr of 13 and rpm of 6000 I should be seeing 1300 pulses per second. If I spin the shaft by hand i do indeed get the exact amount of pulses I would expect. I have a gear bow with a 12.7:1 ratio . 1 revolution by hand at the driven end gives me 166 pulses. 13 ppr x 12.7 ratio = 166 pulses per rev If anyone has info regarding how to set up the high speed inputs this may be where I am messing up It seems like I may only be getting counts based upon the scan rate and not the HSC I am trying to use. Any though would be greatly appreciated, Chair lift project.ulpr -
Hi ; What is the PLC Model? Do you know what version of VisiLogic was used to program the PLC? Older Versions are still available for download and use. If you do not know what version was used. Get the OS Information from Info Mode, or Connection - Get OPLC Information Ask Support@Unitroncisplc.com what Version of VisiLogic was probably used. - obtain it and install it. Modify the program ( Original that you worked from -- NOT the new one you just did - will not be compatible) DanT
-
-
Blog Entries
-
