Jump to content


  • Content Count

  • Joined

  • Last visited

Everything posted by Juandiaza

  1. I would like to work in a project where I can use my samba and get connection using a modem.? Nowadays is hard to find carriers that provide services in 2G, 3G in the US for the Gemalto EHS6T that Unitronics offer to use with devices. I had tried to get connected in project like send SMS, GPRS but not success. So main carriers like Verizon, AT&T or Tmobile said that those modules are not compatible with their networks. Some of you Can recommend me a modem that I can use to my project that It had been used recently in the US?????? Thanks in advanced.
  2. In my understanding, before to Prepare PLC side modem, I should Initialize PC side Modem first??????? is that correct?????? if YES, when I try to do it with this AT commands below for Defaults: (CINTERION EHS6T modem) +++ ATH |||AT+CFUN=0,1 (ERROR) WAIT 9 AT <PIN CODE> WAIT 3 ATI AT&D1&C1 AT+CLIP=1 AT^SCFG="GPRS/ATS0/withAttach","off" (ERROR) ATS0=1 AT+CSNS=4 AT^SCFG="Tcp/WithURCs","off" WAIT 3 AT^SGCONF=540,8 (ERROR) AT^SCFG="Radio/Band/HandOver",1 (ERROR) I got the last Visiologic Version 9.8.65 recommended by Unitronics
  3. I will send an email with the ERRORS generated by VISIOLOGIC when I try to initialize this modem. Thanks Joe for your help. I appreciate it
  4. Because What happens is when trying to run in Visiologic modem services for my modem in this case CINTERION EHS6T and put the correct com port in my case COM1 and so on. It says The EHST6 modem firmware MUST be version 03.001. For more information click help. But it let me keep moving to next step and when finally hit Initialize PC side Modem It says: 1- Open port 1 9600,N,8,1 27.- Modem Output AT&D1&C1 2- Modem Output AT (Baud Rate:9600)
  5. What software do you use to run those commands? because I tried to use PUTTY and hook up the modem to my USB serial port and pops up the screen in order to put the commands on but it didn't allow me even write anything? I checked the PUTTY software. and reinstalled but it won't work.
  6. I am trying to activate my modem GEMALTO in my Samba 4.3" but I couldn't yet because the provider phone company AT&T ask me what is the IMEI number device and I got this info (See info below). The sticker device says: CINTERION EHS6T USB Barcode: S30960-S2740-A100 (Top Barcode) 357042063006721 (Under barcode) both have 15 digits, I assume that one of this is the IMEI number and tried to activate the SIM card but It won't work, So Does anybody have an idea which
  7. Flex727 and Joe Tauser, Thank you for taking your time to had helped me. I already figured it out. You know what It was. I put the logic ladder in lots subroutine in order to organize my sequence but it won't work like that. I put them in Main Routine and now works perfectly. Now, I am going to pass everything because timer won't work either.
  8. MB 0 is the main button for "1520 Line" you can see it in the first picture on this post in red color. The purpose for this button is once you hit it is able to show to the opartor the Line Assembly (SEE picture next #3) and then allows their report the failure in a specific workstation. I want to hide MB 0 in my HMI if the line is down for some reason through pushbutton MB 40. With respect to Why is my pushbutton assigned to MB 40 because I want to change the state of MB53 once toggle pushbutton is disabled on state "1" .
  9. I am trying to change the status of my "Binary image / switch MB 53 (SEE THE FIRST PRT SC "PRINT SCREEN")the little green light under 1520 Line" once you hit a toggle binary Text image / switch you can see it on SECOND PRT SC right after first. But if you notice MB 53 is SET when the machine is Enable and then when you want to reset it because the machine is disabled MB 53 still SET and won't change the status to red on my HMI. What do you guys recommend me to do over the Ladder in order to SET and RESET MB 53?????????????? Thanks in advanced (FIRST PRT SC)
  10. Thank you Cam. Mine comes with Serial and I installed a Ethernet card. I am going to get the modem and test. I hope will work.
  11. Hi, Cam Yes, I already had the Ethernet card installed. It might work too. It's a good idea. But let's say in the case to implement SMS like a rule for these events in the company which kit Do I have to buy because I can't see on technical info if both works with Samba PLC or where can I find out this... Thanks
  12. After being installed my Ethernet card on my device. The next level for my project is included Text messages to the mechanics everytime that line's production is down for failures. I would like to programme the logic that allows people call for help to somebody else at the workplace. First question: Do I need a GSM modem in order to do this???? in case of Yes, I checked the website and found this two models: Article Description Modems GSM-KIT-16J KIT, MODEM GPRS, CINTERION, BGS2T GSM-KIT-17J-3G
  13. Hey guys, I got a success connection between my PLC and yhe Apps after several times. What I did was get all the info through Command Prompt and use the IPv4s Address in this case was (preferred) and set up on computer and my phone and was able to communicate each other using the same LAN. I tried to connect using different LAN it won't work. Thanks to all for your useful comments. It help me a lot.
  14. I don't know What I am doing wrong but I can't connect my PLC via Remote Operator. I did it as help said My IP address is Socket 1 and Port 20256 over the App I set up like this But when I Check PLC Connection said "Connection to PLC Failed" Any suggestions for this???????? Thanks in advanced 1 Drag files here to attach, or choose files... Max total size 0.98MB Insert other media
  15. Hey Dan. I already change the default setting and did what you said and It's working. Thank you soo much
  16. Hi, everyone I need some help to connect my incremental encoder 600 p/min 24 volts to my project I'd been trying to connect my encoder in order to read the pulses on my HMI but I don't know how I do that?????? I wire it up as the schematic. The encoder comes with 4 wires Red, Black, Green, and White. Red = Vcc = here I linked + 24 volts Black = 0 = here I linked 0 Volts Green = Phase A = I linked with Input terminal block (I 0 ) as show schematic PLC diagram White = Phase B = I linked with Input terminal block (I 1 ) as show schematic PLC diagram My q
  17. The model is R20. Is there a way to support if I add any accesories? Thanks
  18. Hello, I am new in all of this PLC field but I want to start with small projects in order to get some experience and then moving on bigger projects. I want to put a graph in my HMI (I actually did it a Variable thermometer Graph MI 12) and see the real temperature value over the graph. According to the Analog Input Wiring, I know that my input (9) AN0 and input (10) AN1 are the inputs. First question: When I start to wire up. Do I just put a wire in AN0 and the other in AN1???? or should be connecting in parallel with V + one side and the other side with 0 - references????? And
  • Create New...